How To Install Touchless Kitchen Faucet?

A touchless kitchen faucet is a great addition to your kitchen. It makes cleaning hands, dishes, and other items easier. You can also turn it on and off without touching it with dirty hands, which is a great benefit for many people.
 
Installing your own touchless kitchen faucet does require a little bit of work, but it is not too difficult for the average person to do. While the exact installation process may vary depending on the brand and model you choose, we’ll take you through the basics of installing a touchless faucet yourself.
how to install touchless kitchen faucet

The installation process for a touchless kitchen faucet is not much different than installing a standard kitchen faucet. You can install most types of touchless kitchen faucets yourself as long as you have some basic plumbing knowledge. Here is what you need for installing them:

Follow these simple installation steps:

Step 1: Turn off the water supply

The first step is to turn off the water supply to your kitchen sink. This can be done by turning off the valves under your sink that are connected to the hot and cold water pipes.
 

Step 2: Remove the old faucet

Remove the old faucet from under the sink using a basin wrench to loosen and remove any mounting nuts that are holding it in place. You can use a bucket or some rags to catch any water left in the supply lines.
 

Step 3: Clean the sinkhole

When you are done removing the old faucet, clean up the sinkhole by removing any limescale or dirt that may have accumulated over time. This ensures that there are no hidden particles that could get stuck in your new touchless faucet.
 

Step 4: Mount the touchless faucet

Take your new touchless kitchen faucet and mount it to the sink. Place it in such a way that its base is centered on the sink’s center hole, then secure it with a nut and washer from underneath.
 

Step 5: Connect the cable and supply lines

You may need to connect cables from your faucet’s base to other components, such as its control box and any sensors it has. You will also need to connect water supply lines from underneath your sink. It is important that these connections do not leak!
 

Step 6: Install the control box

Install the control box assembly under your kitchen sink, making sure it is located close enough to reach both of your hands while standing in front of your kitchen sink.
 

Step 7: Attached the counterweight to the spray hose

Attach the counterweight to the spray hose and put it into place, making sure that no hoses or connectors are twisted or kinked anywhere along their lengths.
 

Step 8: Insert the batteries or connect the AC adapter

The next step is to insert batteries or connect the AC adaptor for the power supply, depending on the model’s type (most of them are battery-powered).
 

Step 9: Turn the water supply

Once you’re done installing the touchless faucet, turn on the water supply and check if there are any leaks. If everything looks good, you can then turn on your new touchless kitchen faucet and enjoy it.

Listed below are our top picks for installing touchless kitchen faucet

Moen Arbor Touchless Kitchen Faucet

Delta Essa Touch2O Kitchen Faucet

Kohler Malleco Touchless Kitchen Faucet

How to install a Moen touchless kitchen faucet?

With a Moen touchless kitchen faucet, you can easily turn on the water with the wave of a hand. It’s a high-tech upgrade to your kitchen that goes great with other modern accessories in the room.

Installation is easy, but there are steps you’ll want to follow to make sure it’s done correctly. Here are some tips for installing a Moen Arbor with MotionSense kitchen faucet:

1. The sensors on the top and front of the spout should be stripped of their protective labels

2. Install the faucet body together with the data cable and deck gasket in the sinkhole

3. Slide support bracket onto faucet body, and then mount washer with mounting nut under the sink

4. Tighten the mounting nut with a screwdriver through the hole using an installation tool.

5. Feed the small end of the pulldown hose through the faucet body and into the spout 6. The spray wand should be attached to the upper connection of the pull-down hose and the hose nuts should be tightened.

7. Connect pulldown hose to quick connect on bottom of control box

8. Plug the data cable into the port at the bottom of the control box.

9. Hook up hot and cold supply hoses.

10. Install the hose weight.

11. Use a hook to attach the battery holder to the wall and insert the AA batteries.

This video will show you how to install a Moen touchless kitchen faucet.

How to install Delta touch kitchen faucet?

The Delta faucet brand delivers well-made, stylish faucets and related kitchen and bath accessories that are both beautiful and functional. This simple step-by-step guide to installing a new touch faucet in your kitchen will give you the confidence to complete this DIY project.

1. The First step is to mount the faucet to the deck. You have to slide the faucet through the mounting hole. The led light should be directed towards you.
 
2. Secure the faucet underneath the sink with the bracket and tighten it with the special tool that came with the touch faucet.
 
Important tip: ensure that the isolation fits well on the bracket and no metal parts are touching the faucet. Otherwise, the touch control feature of the faucet won’t function properly.
 
3. The third step is to attach waterlines, but before you do so, make sure that your water supply lines are turned off at all times!
Make sure the supply lines are fitted with check valves. Attaching the ferrule to the check stops, and then tightening the retaining nut. Do this for the cold and hot supply lines.
 
4. If everything is tightened you’ll have flush any debris that could be stuck on the lines. Place a bucket underneath the faucet open the handle and turn on the hot and cold water for about 15 seconds or until the water runs clear.
 
5. It’s time to connect the solenoid valve. But first, slide the wight onto the sprayer hose.
 
6. Attach the hoses to the solenoid assembly and secure them with a special clip.
 
7. Connect the c-clip in contact with the bottom of the faucet’s shank. And insert the wire into the solenoid assembly. Make sure the wires aren’t twisted and well isolated from any metal parts.
 
8. Connect the battery box to the solenoid assembly. Delta recommends only using AA batteries and also you should place the battery box far away from the faucet on the cabinet floor.
 
9. Your faucet should now be ready for use. The front led will blink to indicate it is ready for use. Test the touch feature of your faucet by touching anywhere on the spout or handle. If your faucet has a temperature control feature, you can adjust it by turning the handle clockwise or counterclockwise once to set a specific temperature.
 

This video will show you how to install a Touch2O faucet.

How to install Kohler touchless kitchen faucet?

The installation of this faucet is pretty straightforward, but there are a few things that you need to pay attention to.This guide will walk you through the process of installing your Kohler touchless kitchen faucet.

1. With the handle on the right, insert the faucet through the mounting surface.
 
2. From underneath, place the locknut onto the shank and tighten it with an adjustable wrench in a clockwise direction.
 
3. Connect the supply hoses to the supply stops and tighten them.
 
4. At this point you’ll have to flush the lines to remove any debris that could be stuck inside. Flush both cold and hot water lines using a bucket.
 
5. Secure the counterweight to the spray hose about 3 inches from the cabinet floor.
 
6. Connect the wires and hoses to the solenoid valve.
 
7. Attach the solenoid and cover to the mounting bracket
 
8. Now it’s time to open the water supplies. All you have to do is check the faucet to see if there are any leaks and if it is working properly
 

In this video, you will learn how to install a Kohler touchless kitchen faucet.

Are touchless faucets easy to install?

Installing a touchless kitchen faucet is no more different than installing any other type of faucet. They usually come with basic instructions that will walk you through the process. The installation usually is fairly easy and the whole process shouldn’t take more than an hour to complete.

How much does it cost to install a touchless faucet?

The cost of a touchless faucet is often a major factor in the decision to purchase one. But how much does it cost to install one? Typically you will spend between $220 and $266 for the installation of a touchless faucet.

A professional plumber will be hired to assemble, place, and install the faucet. A water supply line will be connected between the current shut-off valve and the faucet. Both leaks and flow will be tested to ensure optimal performance.

While touchless faucets are usually easy to install, if your plumbing isn’t old or damaged you could save some money by doing it yourself!

Do touchless faucets need electricity?

The answer is yes, you do need electricity for touchless faucets to work. Both touch and touchless faucets need electricity. Whether it is via battery or plugged into a wall socket.
Their sensor needs power in order to detect when your hands are under the faucet and tell the solenoid valve to turn on or off accordingly. Without power, they would be just like regular faucets – you would need to turn them on and off manually by touching them with your hands!

Why is my touchless faucet not working?

When you first install a touchless faucet, it may work fine. But after a while, it might start to malfunction. To begin with, check the battery compartment. If the batteries are good and it still doesn’t work, you may need to reset it. Different models have different instructions on how to do this. Sometimes you can just hold down a button for a certain number of seconds; other times you may have to unplug it and leave it alone for several minutes.
Also, you can read our guide on how to troubleshoot your touchless faucet and possible solutions to fix it.

Conclusion

Learning how to install a touchless kitchen faucet yourself can be a great way to save money, especially if you like the idea of doing it yourself but are wary about undertaking an entire plumbing project. Most people have the materials they need on hand, and they can use these instructions as a guide to getting started. So don’t be afraid to give this project a try yourself, and you may be able to save some money in the process.